Having previously relied on conventional non-electric initiation systems, Indonesia-based PT Kaltim Prima Coal (KPC) turned to AECI Mining Explosives’ IntelliShot® electronic blasting initiation system, resulting in improvements in safety and efficiency of drill and blast processes on site.
Located close to Sangatta and Bengalon, East Kalimantan, Indonesia, KPC operates one of the largest open-pit mines in the world with coal resources of 9,275-billion tonnes. The Mine employs a load and haul mining method (truck and excavator) within its numerous pits, which are managed by two mining divisions: Mining Operation Division (MOD) and Contract Mining Division (CMD).
KPC commenced with coal production in 1992 and today moves approximately 500-million BCM of overburden per year, which allows the production of 60-million tonnes of coal. About 80% of the overburden requires drilling and blasting to enable efficient excavation.
The Mine has traditionally used conventional non-electric initiation within its CMD area, where AECI Mining Explosives Indonesia (AECI Indonesia) is contracted as the blasting services provider. This method required a lead-in-Line to be run from the blast location to the firing position. In 2017 this method of initiation consumed approximately 650 m of Lead-in-Line per blast location.
High daily production targets set by KPC require multiple locations from where blasts could be initiated safely. Whilst this is possible within the strict safety parameters set by the Mine, it sometimes requires some clever footwork, especially related to moving expensive capital equipment out of harm’s way. This cumbersome method isn’t always the most efficient and often result in a loss of production time.
Finding a solution
AECI Indonesia, as the incumbent blasting services provider for KPC CMD since 2009, suggested IntelliShot®, the Company’s advanced electronic blasting initiation system.
IntelliShot® has the capability to initiate one or more initiating systems wirelessly, known as remote firing. This application has the ability to generate much needed efficiencies by only using a short length of harness wire as opposed to the cost of a full Lead-in-Line when non-electric blast initiation is applied in the same application.
Any new application of technology at the Mine requires careful planning and demonstration of the ability to safely maintain improvement of these parameters. The AECI Indonesia team embarked on a carefully controlled trial to test the applicability of the system and to ensure that KPC gets the full benefits.
In addition to saving on costly lead-in lines, remote firing application through the IntelliShot® system offers additional safety benefits such as an advanced security system; the possibility to easily initiate the blast at larger and safer distances, allowance for the blaster to fire from locations that give greater visual security of the blast area during firing and eliminating potential slap, snap and shoot that is possible with shock tube.
The introduction of remote firing at KPC was performed as a project and carried out in stages in the CMD area of KPC. Focused KPI targets agreed by the project team were carefully monitored on a daily basis to ensure the best possible outcome.
Reaping the rewards
The Project was conducted in the three CMD contractor pit areas at Sangatta and Bengalon under the management of KPC Drill & Blast Department. AECI Indonesia successfully delivered multiple events of remote firing blasting in all areas. The Team also complied with all safety and efficiency Key Performance Indicator’s.
The average usage of harness wire per remote firing event was around 100 m, compared to 650 m per blast of Lead-in-Line used in conventional blast initiation and has reduced the cost of blast initiation in KPC CMD by over 50%.
“Throughout the trial project of remote firing at CMD pits, AECI Mining Explosives has demonstrated its capability to deliver safe and efficient project to world class operations. Remote firing has successfully delivered quantifiable cost benefits for KPC. We expect AECI Mining Explosives to expand this initiative by introducing remote firing to all blast locations at CMD KPC,” says Yuli Prihartono, KPC Drill & Blast Manager.
Further information is available from:
Michelle Le Roux
Marketing and Communications Manager
Phone: (011) 606-0106
Cell: 082 854 7698
Marketing and Communications Specialist
Phone: (011) 606-0876
Cell: 081 296 2179
For media enquiries please contact:
SJC Creative - Sue Charlton
Tel: 087 701 3860 Cell: 082 579 4263